X
Advertisement

1,041 questions

1,221 answers

205 comments

779 users

Need More Details for http://www.electroschematics.com/8712/rf-based-wireless-remote-control-system/

264 views
0 votes
Need More Details for http://www.electroschematics.com/8712/rf-based-wireless-remote-control-system/

Have not built electronic circuits in many years.  in the drawings for

http://www.electroschematics.com/8712/rf-based-wireless-remote-control-system/

Where does the switch for the transmitter connect?  There has to be an input to tell the transmitter to send a signal, but I do not understand where the switch would connect.

Also, on the receiver, where would the wires to send a signal to the actuator (appliance?) connect to the receiver?

I want to use this in a remote location where there is no power so I also want it to be solar powered?  Any suggestions?

The small motorized valve I want to control is rated at 5 volts,  operating current is 80 mAmps and it only requires 8 seconds to open or close.  Also, as I understand it, the valve will automatically disconnect power when it is either fully open or fully closed.

Any suggestions are appreciated.
asked Aug 12 by peter-greenleafprotonmail-com (120 points)

1 Answer

0 votes

Hi,

Download datasheets for the part and study them to begin.

Pin 14 in the transmitter schematic is the transmit control.  Connecting it to 0v makes the part transmit.  In the schematic it is permanently tied to 0V so it will transmit continously.

On the receiver scjhematic pin 17 ( VT ) is the output pin.  It is set to the supply voltage ( +5V ) when the address line settings on both the transmitter and receiver are set the same.

The output control circuitry shown ( after K1 ) probably needs to change.  It depends on the requirements of the valve you want to use.

For power the easiest probably would be to use a battery and some form of solar charger for the battery.  Pick the battery technology you wish to use and then select a proper solar powered charger for that battery technology.

Specifics about the valve control are really dependant on the specific valve you want to use.  Are there 2 inputs for direction control?  Or is a supply voltage polarity swap needed?

A possibility would be to use 2 HT12F decoders fed by the 1 receiver.   One would provide a "OPEN" control signal while the other would provide the "CLOSE" control signal.  The 2 decoders would have their address lines set differently.  Then on the transmitter would be a SPST switch controlling 1 address line.  This switch would choose "OPEN" or "CLOSE" function.  Then another switch to assert the transmit pin ( or just the power and the transmit pin is permanently connected to 0V ).  You would hold the transmit switch until the valve had completely moved to the desired operating position.

Pat
answered Sep 3 by es-pdcopolydevelopment-com (140 points)

Related questions

  • 0 votes
answered Jan 3, 2013 by admin (6,160 points)
  • 0 votes
answered Dec 20, 2012 by admin (6,160 points)
  • 0 votes
  • 1 answer
  • 484 views
  • 1 vote
answered Mar 19, 2013 by j-keith (12,800 points)
  • 0 votes
answered Feb 24, 2013 by j-keith (12,800 points)

1,041 questions

1,221 answers

205 comments

779 users

Latest Article Comments

IT = CV …or what I never learned in tech...
">> what happens when time becomes infinite??? tl;dr; It won't! Really NOT! Trust me, I'd"
Audio Compression Amplifier...
"Hi Keith, An Excellent AGC/ Compression circuit, you have done. Is there a way to calibrate"
Home IoT - Voice Controlled Lab Lights with Amazon Alexa and...
"I could could see this being used in a home theater. Or even better, I could see this being used"
Battery Backup...
"any way you can help with a schematic"
Hacking a Camera Shutter with Infineon TLE94112LE and Arduino - Part...
"Hey Adam! Me too. I always draw by hand many of my first schematic design. It is easier and faster"
36V Battery Level...
"Hi. Can I add a 12 volt relay for alarm on this 24 v batt level indicatator Circuit.any"
Hacking a Camera Shutter with Infineon TLE94112LE and Arduino - Part...
"I really love the hand drawn artwork. I use things like this a lot to help me gather my"
Visualizing Data with...
"@Adam: Let's going on... Processing Overview - https://processing.org/overview/ Artificial"
Talk Over...
"can you tell us about what that components code are ? i'm new at this so i don't know some of"
Visualizing Data with...
"I was not aware of the Processing pakage for plotting. I will have to go and take a look at"
electroschematics group on facebook
...
  Search 4 million + Products
Browse Products