Advertisement
long range fm transmitter

Long Range FM Transmitter

This is very stable, harmonic free, long range fm transmitter circuit which can be used for fm frequencies between 88 and 108 MHz. This can cover 5km range (long distance). It has a very stable oscillator because you use LM7809 stabilizer which is a 9V stabilized power supply for T1 transistor and for frequency adjustment that can be achieved by using the 10K linear potentiometer. The output power of this long range rf transmitter is around 1W but can be higher if you use transistors like KT920A, BLX65, BLY81, 2N3553, 2SC1970, 2SC1971…

T1 is used as an oscillator stage to deliver a low power stable frequency. To adjust the freq. use the 10k linear potentiometer like this: if you trim down, towards ground, the freq. will drop and if you adjust it toward + it will rise. Basically the potentiometer is used as a variable power supply for the two BB139 varicap diodes. Those two diodes act like a variable capacitor when you adjust the pot. By varying the diode capacitance the L1 + diodes circuit makes a resonance circuit for T1. You can use transistors like BF199, BF214 but do not use BCs. At this moment you don’t have yet the long range fm transmitter because the power is quite low, no more than 0.5 mW.

How does long range fm transmitter works

Make sure to encase the oscillator stage in a metallic shield to prevent parasite frequencies destabilizing the oscillating stage.

T2 and T3 works as a buffer stage, T2 as a voltage amplifier and T3 as a current amp. This buffer stage is very important for freq stabilization because is a tampon circuit between the oscillator and the preamp and final amplifier. It is well known that poor transmitter designs tend to modify freq. as you adjust the final stage. With this T2, T3 stage this won’t happen anymore!

T4 is a preamplifier for the fm transmitter and is used as a voltage power rf amplifier and will deliver enough power to the final T5 transistor. As you can see T4 has a capacitor trimmer in its collector, this is used to make a resonance circuit that will force T4 to amplify better and get rid of those unwanted harmonics. L2 and L3 coils must be at 90 degrees angle one to another, this is to avoid frequency and parasite coupling.

The final stage of the long range rf transmitter is equiped with any rf power transistor that has at least 1 watt output power. Use transistors like 2N3866, 2N4427, 2N3553, BLX65, KT920A, 2N3375, BLY81, 2SC1970 or 2SC1971 if you want to have a pro fm transmitter with enough power to cover a long range area. If you use 2N2219 you will get no more than 400mW. Use a good heatsink for the T5 transistor as it gets a little hot. Use a good 12V/1Amp minimum stabilized power supply.

Long range fm transmitter circuit diagram

long range fm transmitter

click on the schematic image for larger view

T1 = T2 = T3 = T4 = BF199
T5 = 2N3866, 2N4427 or 2SC1970 for 1Watt / 2SC1971, BLX65, BLY81, KT920A or 2N3553 for 1.5 to 2W power.
L1 = 5 turns / 0.6mm / 4mm silvered copper
L2 = 6 turns / 0.8mm / 6mm enamelled copper
L3 = 3 turns / 1mm / 7mm silvered copper
L4 = 6 turns / 1mm / 6mm enamelled copper
L5 = 4 turns / 1mm / 7mm silvered copper

Use silvered copper for L3 and L5 if you want to obtain better characteristics.

Adjustments of the long range transmitter

Start by construction the oscillator stage, solder a small wire to T1 10pF capacitor out and listening to a fm receiver, trim the 10k pot untill you can “hear” a blank noise or if you plug in an audio source you can hear the music. With a 70cm wire you can cover a 2 – 3 meter area just with the oscillator stage.

Then continue to build the rest of the rf transmitter, use proper shielding as indicated in the circuit schematic. When you finished the transmitter construction connect the antena or better a 50 or 75 Ω resistive load and use this rf probe, you can use 1N4148 diode instead of the probe diode.

Adjust again the 10k pot to desired freq. and then go to T4 stage and trim the first collector trimmer for maximum voltage indication on the multimeter. Then continue with the next trimmer and so on. Then go back to the first trimmer and readjust again untill you obtain the highest voltage on the multimeter. For 1 watt rf power you can measure a 12 to 16 Voltage. The formula is P (in watt) is equal to U2 / Z, where Z is 150 for 75Ω resistor or 100 for 50Ω resistor, but you must remember that the real rf power is lower.

After those adjustment, if everything is going well connect the antenna, continue using the rf probe, readjust again all the trimmers starting from T3. Make sure you don’t have harmonics, check your TV and radio set to see if there is disturbance on the band. Check this in another room, far away from the fm transmitter or antenna.

That’s all folks 😀 … This is my design for a long range transmiter and is working well. I used 2SC1971 which has a 12dB power gain in 88 … 108 MHz band, this is around 15 times rf amplification. As T4 delivers around 80 to 100 mW of rf power the final stage has enough power to deliver between 1 to 2W depending the transistor usage.

164 Comments

Join the conversation!

Error! Please fill all fields.
  • TECH

    WHATS THE COVERAGE AREA IN KM FOR THIS CCT

    • P. Marian

      it’s huge (with this power can be more than 5 km) if you have a very good antenna and low loss cable, and less than a few meters if you have a poor antenna and high loss coaxial cable.

  • Simon

    Can anyone get me a completed project. Most of the parts used are not in our local shops. If you can have an already working then you can sell one to me.
    +254720000185

  • Anum

    plzz tell me i want to use inductor instead of coil L1,l2,etc… tell me the value of inductor or formula how to calculate??? plz tell as soon as possible…

    Thank you 🙂

  • prasad

    is there any single chip particular ic for audio/voice transmission in should include mic also and for receiver if there means tell i want it so and i want range minimum 500m.

  • shiven

    the resistor after the L3 is mentioned like 58…68 and the capacitor T3 and T4 is 33…100pf. What does this means? What value of components do we have to use..???

    • P. Marian

      58 means 58Ω resistor, this is the way values of resistors is often mentioned. T3 and T4 are transistors not capacitors. All the values are presented in the schematic and article.

  • shiven

    what kind of antenna do we have to use with this circuit?? and how can we shield this thing….

  • Bobby

    Can anyone tell me what 100 / 0.5W is. Am I right thinking its a 100k

  • JULIUS

    i have bought all the components but I’m still confused as to where to connect my terminals for the power supply to the system

  • Axel

    Hello my name is Axel, and i am from Greece. I am interested to build a very small radio transmitter to cover a humble area of 5 km maximum, because i the village i live there is ABSOLUTELY NO radio receiving from ANY STATION, so i decided to stop the drama in my village, this design here looks great, but it would be very kind if anyone could send me a detailed plan of the name of the components i will use to do my job. I than you in advance.:)
    my email: axel.sandi@gmail.com

  • prasad

    will u pls give me more details about this project?how it can be used in colleges?

Looking for the latest from TI?